BroodMinder-W3 Kit Guide
Overview
Tip
If you acquired a W3 uncalibrated-unassembled model you should first start with the Circuit board assembly about how to assemble (solder) board with loadcells.
Tip
We suggest that you watch the videos from Section DIY/W3 in the video Library.
The first section of this document demonstrates the fixed feet version followed by the swivel feet version. There is also an appendix to explain modification for Fixed to Swivel W3.
BroodMinder-W3 Assembly - FIXED FEET
Hardware
Reference | Item Description | Qty | Metric (mm) |
---|---|---|---|
A | Phillips Flat Head # 7 x 5/8" | 2 | 3x20 |
B | #8x4" Drywall Screw (W3PA & W3UA) | 3 | 4x70 |
C | #3 3/4 Phil Brass Flat Wood Screw | 16 | 3x20 |
D | Load Cell Custom Support | 4 | |
E | Spline Material | 1 | |
F | Electronics Assembly | 1 | |
user provided | 16.5 Inch Pine 2x4 (adjust for hive width) | 2 | 430x40x60 |
user provided | 15-16 Inch Pine 2x4 | 1 | 420x40x60 |
Prepare the frame members
- Cut your 2x4s to length.
- The length of the end boards should be enough to span the width of your beehive. We typically make them about 16.25โ-16.50" long for a typical 10 frame Langstroth hive. The length of the connecting board is not critical but should be around 16โ.
- Cut saw kerfs (1,2,3) as shown in the picture below. They should be around 0.4โ -0.75โ deep. These will hold the wires from the sensors.
- Cut kerf 4 for the wires to reach the electronics box. (see picture farther down).
- Test fit the spline and widen the kerfs if necessary.
- Remove the broad area (marked 5) with a chisel so that when the 2x4 tips it does not pinch the wire.
Screw together the frame (Fixed Feet)
Once youโre sure everything is where it needs to be, use 3 letter B screws to secure the boards together.
To assemble your frame, make sure you have a flat surface and ensure your pieces are square. Follow the picture above for the correct orientation of the boards.
Leave the side with 1 screw very slightly loose so that the board may pivot.
Attach the electronics box
Make sure the box is located center in the frame with the hole opening as shown. There should be a slight gap between the edge of the frame and the box as shown. Use (2) โAโ screws.
Sensor Mounting
Position sensors marked 1-4 as shown with mounts โDโ as shown.
Use 4 โCโ screws per sensor.
IMPORTANT: Do not fully tighten these screws. Bending the senor will create a measurement error. Tighten then back off ยฝ turn.
Wire Routing
Tuck the wires into grooves and secure with spline material โEโ. To secure spline material press into groove with flat object, this allows wires to move in the bottom of groove. Do not create stress on the wires. Remove (2) circuit board mounting screws. Pull the slack wire into electronics box and fold wire behind circuit board, reinstall mounting screws. Secure spline material with staples.
Finish and Enjoy
Now you can remove the battery tab and replace the lid on the electronics box and enjoy your new BroodMinder beehive scale.
BroodMinder-W3 Assembly - SWIVEL FEET
Hardware
Item Description | Qty |
---|---|
(Picture A) Phillips Flat Head # 7 x 5/8" | 2 |
(Picture B) #8x4" Drywall Screw (W3PA & W3UA) | 3 |
(Picture C) #10 ยพโ SS Round Head Screw | 4 |
(Picture D) Load Cell Custom Support | 4 |
(Picture E) Swivel Feet | 4 |
(Picture F) Spline Material | 1 |
(Picture G) Electronics Assembly | 1 |
16.5 Inch Pine 2x4 (User provided) (16.5 inch or adjust for hive width) | 2 |
15-16 Inch Pine 2x4 (User provided) | 1 |
Prepare the frame members
- Cut your 2x4s to length.
- The length of the end boards should be enough to span the width of your beehive. We typically make them about 16.25โ-16.50" long for a typical 10 frame Langstroth hive. The length of the connecting board is not critical but should be around 16โ.
- Cut saw kerfs (1,2,3) as shown in the picture below. They should be around 0.4โ -0.75โ deep. These will hold the wires from the sensors.
- Cut kerf 4 for the wires to reach the electronics box. (see picture farther down).
- Test fit the spline and widen the kerfs if necessary.
- Remove the broad area (marked 5) with a chisel so that when the 2x4 tips it does not pinch the wire.
- Drill qty 4, ยพโ holes. The centers should be ยพโ from the edge and ยพโ deep
Screw together the frame
Once youโre sure everything is where it needs to be, use 3 letter B screws to secure the boards together.
To assemble your frame, make sure you have a flat surface and ensure your pieces are square. Follow the picture above for the correct orientation of the boards.
Leave the side with 1 screw very slightly loose so that the board may pivot.
Attach the electronics box
Make sure the box is located center in the frame with the hole opening as shown. There should be a slight gap between the edge of the frame and the box as shown. Use (2) โAโ screws.
Sensor Mounting
Use 1 โCโ screws per sensor.
Wire Routing
Tuck the wires into grooves and secure with spline material โEโ. To secure spline material press into groove with flat object, this allows wires to move in the bottom of groove. Do not create stress on the wires. Remove (2) circuit board mounting screws. Pull the slack wire into electronics box and fold wire behind circuit board, reinstall mounting screws. Secure spline material with staples.
Finish and Enjoy
Now you can remove the battery tab and replace the lid on the electronics box and enjoy your new BroodMinder beehive scale.
Tip
If you acquired a W3 uncalibrated-unassembled model you still need to calibrate your scale. Jump to the Scale calibration section
Appendix: Update fixed feet W3 scales to swivel feet
If you have an Apimaye hive, you may want to upgrade your W3 to include the swivel feet mounting.
This is quite easy except for one step. Removing the fixed feet from the W3 kit is quite difficult because there is no screw head to grab and the feet are fixed with permanent Loctite.
We have tried removing them here at Bees on Main and boyโฆ they are difficult.
Therefore, we recommend modifying the load cell holder and using the load cells with fixed feet. The modification is needed so that the foot reaches the ground.
All that you must do is remove the skirt that captures the swivel foot.
Appendix: W3 Unassembled-Uncalibrated parts
Here are all the parts for a W3 scale H model type :
(only missing the Spline material)
)